Managing the Passerelle de déplacement des données server

This topic describes the various connectivity and management options that are available after you have installed Passerelle de déplacement des données.

Updating the Qlik Cloud tenant URL

You can change the Qlik Cloud tenant URL as needed.

To do this:

Run the following command to stop the Passerelle de déplacement des données service:

sudo systemctl stop repagent
Check that the service has stopped by running the following command:

sudo systemctl status repagent

Le statut doit être comme suit :

Active: inactive (dead) since <timestamp> ago
Change the working directory to:

/opt/qlik/gateway/movement/bin

Then run the following command to set the Qlik Cloud tenant URL:

Syntax:

./agentctl qcs set_config --tenant_url URL

Example:

./agentctl qcs set_config --tenant_url mytenant.us.qlikcloud.com
Run the following command to start the Passerelle de déplacement des données service:

sudo systemctl start repagent
Check that the service has started by running the following command:

sudo systemctl status repagent

The status should be as follows:

Active: active (running) since <timestamp> ago

Updating the Qlik Cloud tenant URL also requires you to generate a new registration key and register it in Administration > Data gateways. For details, see Stage two: Install and set up Passerelle de données - Déplacement des données on a server behind the firewall protecting your data sources, and Stage three: Return to Administration and register Passerelle de données - Déplacement des données).

Connecting to cloud data warehouses via a proxy server

You can configure the Passerelle de déplacement des données to connect to your cloud data warehouses via a proxy server. You can also disable proxy server connectivity should it no longer be required.

This proxy is only used for the connection between Passerelle de déplacement des données server and your cloud data warehouses.

Enabling or editing proxy server connectivity

You can enable or edit proxy server connectivity as follows:

On the Passerelle de déplacement des données server, open a shell prompt and change the working directory to:

/opt/qlik/gateway/movement/bin
Run the following command to stop the Passerelle de déplacement des données service:

sudo systemctl stop repagent
Check that the service has stopped by running the following command:

sudo systemctl status repagent

Le statut doit être comme suit :

Active: inactive (dead) since <timestamp> ago
Run the following command to set the proxy:

Syntax:

./agentctl qcs set_config --proxy_url https|http://host:port --proxy_username username --proxy_password password

Example:

./agentctl qcs set_config --proxy_url https://myproxy:1212 --proxy_username admin --proxy_password f56weqs@
Run the following command to start the Passerelle de déplacement des données service:

sudo systemctl start repagent
Check that the service has started by running the following command:

sudo systemctl status repagent

The status should be as follows:

Active: active (running) since <timestamp> ago

Disabling proxy server connectivity

You can turn off proxy server connectivity as follows:

On the Passerelle de déplacement des données server, open a shell prompt and change the working directory to:

/opt/qlik/gateway/movement/bin
Run the following command to stop the Passerelle de déplacement des données service:

sudo systemctl stop repagent
Check that the service has stopped by running the following command:

sudo systemctl status repagent

Le statut doit être comme suit :

Active: inactive (dead) since <timestamp> ago
Run the following command:

./agentctl qcs set_config --proxy_url ""
Run the following command to start the Passerelle de déplacement des données service:

sudo systemctl start repagent
Check that the service has started by running the following command:

sudo systemctl status repagent

The status should be as follows:

Active: active (running) since <timestamp> ago

Viewing the current settings

You can view the current Passerelle de déplacement des données settings (for example, Qlik Cloud tenant URL, proxy URL, and so on).

To do this:

Open a shell prompt and change the working directory to:

/opt/qlik/gateway/movement/bin

Run the following command:

./agentctl qcs show_config

Your current settings will be shown.

[qlik@gatewayhost bin]# ./agentctl qcs show_config
--tenant_url “tenant.qlik.com”
--proxy_url “”
--proxy_username “”
--connection_mode “DATA_GATEWAY”
--listening_address “localhost”
--listening_port “443"
ReplicateAgent Control Program completed successfully.

Passerelle de déplacement des données service commands

Before changing a setting on the Passerelle de déplacement des données server, you need to stop the Passerelle de déplacement des données service, and then start it once the setting has been changed.

Stopping the service

Run the following command to stop the Passerelle de déplacement des données service:

sudo systemctl stop repagent
Check that the service has stopped by running the following command:

sudo systemctl status repagent

Le statut doit être comme suit :

Active: inactive (dead) since <timestamp> ago

Starting the service

Run the following command:

sudo systemctl start repagent
Check that the service has started by running the following command:

sudo systemctl status repagent

The status should be as follows:

Active: active (running) since <timestamp> ago

Restarting the service

Run the following command:

sudo systemctl restart repagent
Check that the service has started by running the following command:

sudo systemctl status repagent

The status should be as follows:

Active: active (running) since <timestamp> ago

After starting the gateway service, you must refresh your browser to see the updated data gateway status (Connected) in Administration > Data gateways.

Cette page vous a-t-elle aidé ?

Si vous rencontrez des problèmes sur cette page ou dans son contenu – une faute de frappe, une étape manquante ou une erreur technique – faites-le-nous savoir.

Laissez vos commentaires ici