Managing the Data Movement gateway server

This topic describes the various connectivity and management options that are available after you have installed Data Movement gateway.

Updating the Qlik Cloud tenant URL

You can change the Qlik Cloud tenant URL as needed.

To do this:

1. Run the following command to stop the Data Movement gateway service:

   sudo systemctl stop repagent

2. Check that the service has stopped by running the following command:

   sudo systemctl status repagent

   De status zou als volgt moeten zijn:

   Active: inactive (dead) since <timestamp> ago

3. Change the working directory to:

   /opt/qlik/gateway/movement/bin

   Then run the following command to set the Qlik Cloud tenant URL:

   Syntax:

   ./agentctl qcs set_config --tenant_url URL

   Example:

   ./agentctl qcs set_config --tenant_url mytenant.us.qlikcloud.com

4. Run the following command to start the Data Movement gateway service:

   sudo systemctl start repagent

5. Check that the service has started by running the following command:

   sudo systemctl status repagent

   The status should be as follows:

   Active: active (running) since <timestamp> ago

Connecting to cloud data warehouses via a proxy server

You can configure the Data Movement gateway to connect to your cloud data warehouses via a proxy server. You can also disable proxy server connectivity should it no longer be required.

Enabling or editing proxy server connectivity

You can enable or edit proxy server connectivity as follows:

1. On the Data Movement gateway server, open a shell prompt and change the working directory to:

   /opt/qlik/gateway/movement/bin

2. Run the following command to stop the Data Movement gateway service:

   sudo systemctl stop repagent

3. Check that the service has stopped by running the following command:

   sudo systemctl status repagent

   De status zou als volgt moeten zijn:

   Active: inactive (dead) since <timestamp> ago

4. Run the following command to set the proxy:

   Syntax:

   ./agentctl qcs set_config --proxy_url https|http://host:port --proxy_username username --proxy_password password

   Example:

   ./agentctl qcs set_config --proxy_url https://myproxy:1212 --proxy_username admin --proxy_password f56weqs@

5. Run the following command to start the Data Movement gateway service:

   sudo systemctl start repagent

6. Check that the service has started by running the following command:

   sudo systemctl status repagent

   The status should be as follows:

   Active: active (running) since <timestamp> ago

Disabling proxy server connectivity

You can turn off proxy server connectivity as follows:

1. On the Data Movement gateway server, open a shell prompt and change the working directory to:

   /opt/qlik/gateway/movement/bin

2. Run the following command to stop the Data Movement gateway service:

   sudo systemctl stop repagent

3. Check that the service has stopped by running the following command:

   sudo systemctl status repagent

   De status zou als volgt moeten zijn:

   Active: inactive (dead) since <timestamp> ago

4. Run the following command:

   ./agentctl qcs set_config --proxy_url ""

5. Run the following command to start the Data Movement gateway service:

   sudo systemctl start repagent

6. Check that the service has started by running the following command:

   sudo systemctl status repagent

   The status should be as follows:

   Active: active (running) since <timestamp> ago

Viewing the current settings

You can view the current Data Movement gateway settings (for example, Qlik Cloud tenant URL, proxy URL, and so on).

To do this:

1. Open a shell prompt and change the working directory to:

   /opt/qlik/gateway/movement/bin

2. Run the following command:

   ./agentctl qcs show_config

   Your current settings will be shown.

   Voorbeeld:  

   [qlik@gatewayhost bin]# ./agentctl qcs show_config
   --tenant_url “tenant.qlik.com”
   --proxy_url “”
   --proxy_username “”
   --connection_mode “DATA_GATEWAY”
   --listening_address “localhost”
   --listening_port “443"
   ReplicateAgent Control Program completed successfully.

Data Movement gateway service commands

Before changing a setting on the Data Movement gateway server, you need to stop the Data Movement gateway service, and then start it once the setting has been changed.

Stopping the service

1. Run the following command to stop the Data Movement gateway service:

   sudo systemctl stop repagent

2. Check that the service has stopped by running the following command:

   sudo systemctl status repagent

   De status zou als volgt moeten zijn:

   Active: inactive (dead) since <timestamp> ago

Starting the service

1. Run the following command:

   sudo systemctl start repagent

2. Check that the service has started by running the following command:

   sudo systemctl status repagent

   The status should be as follows:

   Active: active (running) since <timestamp> ago

Restarting the service

1. Run the following command:

   sudo systemctl restart repagent

2. Check that the service has started by running the following command:

   sudo systemctl status repagent

   The status should be as follows:

   Active: active (running) since <timestamp> ago